![]() ![]() with the princess front makeover painted transformation tuesday replacing. Want to hang out more? We do too! Sign up to get our email updates here. To make tempered glass, annealed glass is cut to the desired size and then. Once cured, it was now finally time to start the aging process and Schmidt got stated by first methodically wet sanding. ![]() If you liked this project, we’d appreciate if you pinned it! Just click the button to pin: pin it After laying down two heavy coats, the panel was left to dry for 24 hours. Ready to see what our friends did with their Metal Effects Patina kits? Check out their projects below and if you’d like to see the full tutorial just click the pictures. Pretty cool, huh? The best part is that we didn’t even use half of the paint, primer, and patina solution, so we can still do another project or two. We let it dry overnight and when we came back the next morning it looked like this. Once you spray the patina aging solution, the paint begins to turn dark blue within a few minutes, but you have to let it dry to get the full effect. Here’s what the pot looked like after primer and paint. There was an instruction booklet in the box, but the directions are pretty simple: two coats of primer, two coats of bronze paint, then spritz with the patina aging solution while the paint is still wet. We decided to transform a decorative pot we found at the thrift store. Give the outside of your rifle a good cleaning, wipe it down, get the dirt and grime off, then follow that up with a good spray down with brake cleaner to strip any grease and oil that might still be on the rifle. They have three finishes, blue patina, green patina, or rust, and we chose to work with blue patina. Blast it with brake cleaner to remove all the oil, grease, and dirt. Our Modern Masters Metal Effects kit came with everything needed to complete our project, including the brushes. like like for wine-showed ends of : corks but you coul check out sh: distressed roof job The agedlooking turquoise paint combined with the patina of the. This sponsored post was written by me on behalf of Modern Masters, and may contain affiliate links. It’s only about $12 a can.It’s time for another Monthly DIY Challenge! This month our challenge item is Modern Master’s Metal Effects Patina Paint. ![]() It takes about three cans to do the underside of a short bed truck. It collects dirt over time but a quick blast with the pressure washer and the dirt goes and the fluid film mostly stays. It does not dry out like the Rust Converter. 8 Add 2 ounces of ammonia to a smaller plastic cup. It is now in a contained area where the sample can stay as wet as possible for as long as possible. Swan, a reliable visual reference of perfect black paint would be an Alloway’s Hot Rod Shop car, like the Chevelle they recently finished, or the Rick. 7 Place the wet metal into a 1 gallon plastic bucket. Patina jobs don’t require bodywork, precision sanding, and don’t get cut or buffed, allowing for it to get on the street faster than attempting the perfect black paint job. Avoid applying the paint until your cart is completely dry. Hose off the soap with cold water, and dry off your cart with a towel. Remove all dirt and grime from your cart with an oil-based dish soap. This stuff is a spray film that coats and soaks into your metal to form a protective petroleum-based film. This particular mix is a great way to clean up copper pennies and remove the patina from them as well. Residual dirt can cause your coats of paint to flake or peel. * Finally, if you want to coat the frame rails and suspension, Fluid Film is a good solution. After it soaks in a bit, rub as much as much as possible off the paint as you can with paper shop towels. * At this point you can use boiled linseed oil, not straight linseed oil, to rub a heavy coat into the exposed rust and a thin coat on the rest of the truck. This product stops rust on iron and steel surfaces and converts it into a black coating that seals out moisture and protects against future corrosion. * Rust Converter is perfect for under the wheel wells and cab area. This product is easily available at the grocery store. * After a solid wash, throw on some rubber gloves and start scrubbing the body panels with CLR (Calcium Lime Rust) and green Scotch-Brite pad. PowerNation Apr 28th, 2021 1965 Chevy C10 POWERNATION One of the age old questions when it comes to car restoration is paint versus patina, and with the guidance of Ted Swan, painting specialist with Summit Racing, we hope to settle that debate today. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |